PDA

View Full Version : Wrecks to Riches 94 P'up



Facime
12-12-2011, 08:25 PM
I'll try to keep the boring chatter to a minimum. A few people here knew I had this but its done and up for sale now so I just thought you folks might appreciate the details. Im moving this over from a local forum.


I picked this up from an insurance auction exactly as you see it.

http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/304795_253333541372704_100000881806029_697025_1966 104326_n.jpg

4" trailmaster lift, 33x12.5's on 10" alloys. 148K original miles, 22RE.

It had a little unibody damage just behind the core support and buckled the inner fender under the battery a little. It leaked oil like crazy while running, no drips on shut off, and the front brakes were SHOT.

http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/298636_253333658039359_100000881806029_697027_9976 60671_n.jpg


Looks like a rear main based on where the oil collects.
http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/300743_253333704706021_100000881806029_697028_1263 320315_n.jpg

the oil just spreads out and has coated the underside of this greasy pig
http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/294242_253333754706016_100000881806029_697029_2232 37361_n.jpg


Ive seen worse carpet, but this will come out for cleaning
http://a7.sphotos.ak.fbcdn.net/hphotos-ak-snc7/302131_253333811372677_100000881806029_697031_1010 469372_n.jpg


Door card and seal mangled.
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/304059_253333864706005_100000881806029_697032_2784 85068_n.jpg

tailgate is mangled and handle doesnt work. have to open it from the inside.
http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/314975_253333908039334_100000881806029_697033_1681 125783_n.jpg

comes with a few parts! new grill, bumper, fender, lower valance, 4.80 pumpkins for front and rear, and some other odds and ends that were taken off the truck for its insurance inspection.
http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/296251_253333951372663_100000881806029_697034_1902 033619_n.jpg


The budget for this project is a $1000.

Facime
12-12-2011, 08:25 PM
First things first, I wanted to be able to drive it around so I pulled the unibody damage out and put the front end back together. The unibody was a slight wrinkle behind the core support, behind the headlight. I simply put that corner under traction using a come along and applied a little heat and some heavy persuasion and got everything back where I thought it lined up pretty good again. Sorry no pictures of my super secret methods.

After the skeleton issues were dealt with I went ahaed and reassembled the front end and prefit the fender (it would come back off for painting)

http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/310674_255083947864330_100000881806029_703615_4761 89619_n.jpg

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash4/294216_255084097864315_100000881806029_703618_8717 40554_n.jpg


the lower valance came prepainted in factory color and after a little tweaking here and there everything lined up pretty well
http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash4/306446_255084147864310_100000881806029_703619_3217 24457_n.jpg

I dont have a picture of it before, but the hood had been splashed by battery acid so it was going to need repaint. I also picked up a replacement tailgate that was in much better shape. I had to delete the logo stickers and fill a couple small dings here and there, but it fit the budget.
http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/308685_274646909241367_100000881806029_770378_1165 556417_n.jpg

Primer/surfacer is on
http://a8.sphotos.ak.fbcdn.net/hphotos-ak-snc7/297136_274646982574693_100000881806029_770380_8145 85124_n.jpg


Keeping the woodstove blasting helps make winter work bearable.
http://a2.sphotos.ak.fbcdn.net/hphotos-ak-snc7/385866_274647022574689_100000881806029_770381_1847 253685_n.jpg


The first thing to get color was the tailgate. I have only used my gun setup once before (on my bike) and I was using a different paint this time. I was left with a bit of orange peal.
http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/298184_277029935669731_100000881806029_777660_7550 24896_n.jpg


Considering my experience and working conditions I didnt think it was too bad. It was just a test run of my painting equipment really anyway and it just meant a little more color sanding anyway. After color sanding and buffing it looked pretty good and a vast improvement over what was there:

Before:
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/320760_277502298955828_100000881806029_778908_1617 58816_n.jpg

after:
http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash4/308667_277502488955809_100000881806029_778910_7410 16762_n.jpg


About a week later I finally managed to get color on the hood and fender. This time the spraying went a bit better. Despite ONE DAMN FLY that decided to kamakazi into my basecoat, the overall results were quite satisfying.
http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/381429_288912897814768_100000881806029_807802_3600 34163_n.jpg


http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/377015_288912931148098_100000881806029_807804_1900 282235_n.jpg


dont I look satisfied?
http://a6.sphotos.ak.fbcdn.net/hphotos-ak-snc7/377064_288912977814760_100000881806029_807805_1887 078382_n.jpg

Facime
12-12-2011, 08:26 PM
So I did a little wet sanding and an initial buff and installed the hood and fender on the truck

http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash4/393260_290272184345506_100000881806029_811740_1058 886268_n.jpg



Carpet was pulled, cleaned and reinstalled:
http://a2.sphotos.ak.fbcdn.net/hphotos-ak-snc7/374871_290272237678834_100000881806029_811741_7588 75839_n.jpg

http://a7.sphotos.ak.fbcdn.net/hphotos-ak-ash4/384905_290272341012157_100000881806029_811744_1126 395070_n.jpg



Seat was pulled, and I pulled the covers off the frames and laundered them. If I had a little more budget I would have gone to buckets, but this seat was perfectly serviceable:
http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/375359_290272277678830_100000881806029_811742_6711 21837_n.jpg




the advantage of going to the same guy for my junkyard parts whenever possible is sometimes I get really good treatment. I managed to get a door card and seal for absolutely nothing. The door card was soaking wet and an slightly warped, but several days near the woodstove with some cinder blocks on it and it dried perfectly straight.

http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/388373_290272307678827_100000881806029_811743_1188 85947_n.jpg



A final go round with my buffer and the paint was really shining. This is my very first pearl or metallic paint job. Im very happy with the results:
http://a4.sphotos.ak.fbcdn.net/hphotos-ak-ash4/387429_292042350835156_100000881806029_816016_5960 58722_n.jpg



Then the whole truck got a good detail:
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/390051_292042427501815_100000881806029_816018_1803 390432_n.jpg

http://a3.sphotos.ak.fbcdn.net/hphotos-ak-snc7/393686_292042454168479_100000881806029_816019_2763 49862_n.jpg


The paint wasnt a perfect match. Its a little deeper color. But for a "wheeler" I didnt think it really mattered.
http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/376026_292042480835143_100000881806029_816020_8821 65172_n.jpg



And that completed the cosmetic portion of the job:
http://a5.sphotos.ak.fbcdn.net/hphotos-ak-snc7/388673_292720900767301_100000881806029_817242_3391 54760_n.jpg

http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/374199_292720927433965_100000881806029_817243_9838 1365_n.jpg

http://a8.sphotos.ak.fbcdn.net/hphotos-ak-ash4/377384_292720967433961_100000881806029_817245_1598 193318_n.jpg

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-snc7/381154_292720954100629_100000881806029_817244_2110 699592_n.jpg

Facime
12-12-2011, 08:26 PM
I didnt really take any interesting pictures of the mechanical work. I swapped out the gears for the 4.80's. The rear was easy, the front was a bit of a nightmare. Those carriers are awfully damn heavy and hard to manipulate around.

I found a bad CV boot while in there so I replaced that, and the front brakes were completely redone with reman calipers and new rotors and ceramic pads.

The oil turned out to NOT be the rear main but something really stupid. The oil filter wasnt as tight as it should be. I didnt actually discover this until I went to replace the oil pressure sender. I went ahead and pulled the oil pan and ditched the cork in favor of FIPG. After all that and an oil change and some diligent pressure washing, I got the underside looking nice again and ZERO leakage.


Here is a complete list of all the parts and supplies I bought for the truck




1 Used Tailgate (B&R Auto wrecking) 75.00
2 Disc brake caliper @41.99ea. 83.98
1 Misc hardware (Napa Auto Parts) 31.14
2 Front brake rotor @36.98ea. 73.96
1 Front brake pads, ceramic, premium 45.87
1 Brake cleaner 4.38
1 Prestone 50/50 7.44
1 Half time premium body filler 22.19
1 hardener 3.88
25 Sanding disks @.88ea. 22.00
1 Scuff pad 1.98
1 Oil pressure switch 58.99
1 CV driveshaft 49.99
1 CV driveshaft core 11.00
5 QT 5/30 valvoline semi-syn @4.49ea. 22.45
1 Napa gold oil filter 4.84
2 Shop towels @2.69ea. 5.38
1 Tube of FIPG (John and Phil's Toyota) 15.99
1 Gal. Lacquer Thinner 14.99
1 Qt Primer surfacer 14.99
1 Qt. Reducer 8.09
2 Pack w/d 1500grit sandpaper @2.99ea. 5.98
1 Qt. Omni Basecoat 47.69
1 Qt Medium reducer 11.79
1 Qt Hi-Gloss Muli-panel clear 21.74
1 Qt topcoat hardener 51.14
1 Qt 2K sealer 28.26
1 1/2pt. sealer hardener 18.48
1 Gal. Wax/Grease remover 24.73
4 Mixing cups @.43ea. 1.72
1 Qt Swirl remover 14.88
1 Qt medium cleaner compound 13.88

TOTAL $819.00


So I came in under budget! Thats rare for me.


*These trucks are like gold here in the NW. I asked a rediculous price for the truck and sold it within a few days for a net profit of around $1800. *

Funkycheeze
12-12-2011, 09:42 PM
Nice! I have a '92 V6 with the factory 4.56 gears and 31s. Plan on doing a 3.4L (5VZ) swap and all sorts of other madness with lockers, trail armor and fibreglass etc.

Good trucks.

Aaron Willis
12-12-2011, 09:45 PM
Damn. Impressive work, and a nice result to boot. Well done. Looks like I am in the wrong business.

MCcelica
12-12-2011, 10:35 PM
That is most definitely some nice work. :)

Luni
12-12-2011, 11:39 PM
You damn hippie.

You do such good work. Great job man!

CollapsedNut
12-12-2011, 11:49 PM
When my 4th gen is done Ima ship it to you....

Facime
12-13-2011, 02:02 AM
Thanks guys! I was kinda lazy on this one and, lesson learned, never try to paint in the dead of winter without a heated/ventilated booth. I actually ended up getting a case of cyanide poisoning from the 2K paint I used. Im back to just doing detail jobs for now and will be prepping my 6th gen for sale this spring. Also made a contract job with a customer to do 4 restorations for him this next year. Hes got a 65 Galaxy 500 unrestored original, a couple early 60's T-birds and a Hillman Minx that all need some special attention, so that should keep me pretty busy.


Got a new dog and SWTOR is releasing this week so Im gonna just hibernate for the winter though ...and just be a hippie! ;)

Car_Barn_Bandit
12-13-2011, 02:11 AM
They had a GORGEOUS 66' Galaxie at the PAP a couple months back. Real shame that car ended up in there. Great shape.

pintoBC_3sgte
12-13-2011, 03:29 AM
hot damn! always amazed by your work :)

alltracman78
12-13-2011, 04:05 AM
Nice

I love the 89 - 95 trucks, they're my favorite body style.
I'm planning on sticking a 1UZFE in mine when the engine dies.

T-spoon
12-13-2011, 05:01 AM
Dang, you are one resourceful dude. Looks great :)