PDA

View Full Version : 2nd gen 3SGTE into 6th gen Celica pics



Dr Tweak
07-17-2010, 12:38 AM
Hi guys,

Little update on one of the projects in the shop, this is a 6th Gen that's had a 3SGTE bolted into it for a few years now, because of various issues the owner wasn't able to find someone to get it finished, until it ended up here.

What it looked like when it showed up:

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan1.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan2.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan3.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan4.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan5.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan6.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan7.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan8.jpg

Cleaning process....

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan9.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan10.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan11.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan12.jpg

We checked the timing belt and found both cams to be a tooth off, so we had to redo that.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan13.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan14.jpg

Cleaned up the wiring harness...

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan15.jpg

Details: Fuel filter rotated so that the banjo to AN adapter can make use of the stop on the filter when tightening the bolt. Wiring harness secured with cushion clamps where needed.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan16.jpg

Details: Stainless line covered with glue-lined heatshrink where it gets close to the wiring harness. This will prevent any chance of the stainless braiding wearing away at the loom.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan17.jpg

True cold air intake

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan18.jpg

Stainless line where it connects to the rail.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan19.jpg

Coil/igniter relocated off the firewall to clean things up. Also relocated the MAP sensor off the firewall and hid the resistor pack out of view.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan20.jpg

True cold air intake, note that factory cruise control has been retained, with plenty of clearance between the bracket and the intake piping.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan21.jpg

Another view of the cold air intake location.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan22.jpg

Overall view. Engine is waiting on a new fuel pressure regulator and injector clean/balance/flow test before starting.

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan23.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan24.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan25.jpg

vip09
07-17-2010, 03:23 PM
Looks great as always Tweak!

Hookecho
07-17-2010, 04:42 PM
It looks really good! I'm sure the owner will be glad to get it back in great working order.

Smaay
07-17-2010, 10:06 PM
very nice

Nitro_Alltrac
07-18-2010, 04:43 AM
Great work Tweak! It's looking really good.

Dr Tweak
07-20-2010, 04:54 PM
Thanks for your kind comments. After giving the fuel problem some more thought I was suspicious about the fuel pump installation. We pulled it out and found this:

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan26.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan27.jpg

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan28.jpg

Looks like they used a piece of heater hose for the fuel line. For those that don't know, fuel and oil will eat right through a heater hose. So the pump was pushing a little bit of fuel up to the rail but not enough to open the regulator. We redid the fuel pump install...

http://www.phoenixtuning.com/toyota/swaps/anh-tuan/anh-tuan29.jpg

And then after resuscitating the injectors, it started up on the first try :)

UndaGrwnD
07-20-2010, 05:09 PM
looks like a fresh gen2

ChrisD
07-20-2010, 05:23 PM
Nice! Wow, to be honest I had never known about that either. However I've always just used whatever hose came with the pump or the original that was there if it was in good shape.

Are they sticking with the ATA IC? Plans for a scoop if so?

vangls14
07-21-2010, 06:57 PM
Nice work. I'm sure the owner will be delighted by the quality of your work. A half-trac is pretty damn fast.