PDA

View Full Version : I give up on my Celica's..



acidice333
07-31-2009, 01:08 PM
I think I'm calling it quits on my two Celica's.

My white one, the engine blew.. $221.23CAD to tow it 50KM from where I broke down. It still starts, but won't stay running unless I give it gas. Loud ass knocking noise. ..and the head was gawd damn rebuilt not even 3000KM ago!

This is pissing me off ): Why do you guys all have to be in the States ):

I wanna keep it... but I need a replacement engine.. but the junkers here are gonna rape me... anybody close to BC have something?

ChrisD
07-31-2009, 04:10 PM
Got a warranty on the rebuild? 3000 km's is still within breakin period usually.

Mafix
07-31-2009, 04:15 PM
you rebuilt the head and threw it on a stock block?

H8PVMNT
07-31-2009, 04:54 PM
Time to bite the bullet and learn to rebuild your bottom end at home...

ChrisD
07-31-2009, 05:08 PM
my bad, missed the keyword "head"

i would get a jdm engine personally...ahem 3sgte... ;)

acidice333
07-31-2009, 06:57 PM
I would too but 2-3k for one I just don't know... If it wasn't so damn expensive, I'd go for it..

I'm kinda scrapped for money... I might just find a bottom end, and slap that together with the rebuilt head.. anybody got a bottom?

rizin
08-01-2009, 02:16 AM
I would build a short block. Sounds like a rod bearing.

TCgts
08-04-2009, 06:27 AM
i used to have a 93 gt and had nothing but problems.....Blew the first motor with only 160,000km on it. And then i got a new one and had nothing but problems with it aswell. So i sold it and jus got a new car, problem solved.

KoreanJoey
08-04-2009, 06:38 AM
Wimps.

Oh wait, I swapped to a 3SGE. NM.

acidice333
08-04-2009, 07:42 AM
I've been thinking of going 3SGTE.. but for now probably just throw together a short block..

Hey Joe, find anything for me? You could like find a new engine for me and trek it down along with my hood :D

KoreanJoey
08-04-2009, 08:14 AM
Yeah, I thought about going to Vail for the Kumho Challenge this last weekend but had to work on moms Camry (major overhaul: Valve Cover Gaskets, Timing Belt, Drivebelts, Waterpump, Cam Seals, Crank Seal, ETC).

And doing all this on a 1MZ is the suck.

BUT, I'll make some calls, last I checked it was about 1200 for a 5SFE and about 700 for a 3SFE (JDM).

acidice333
08-04-2009, 08:20 AM
GE or GTE I think would probably be better hopefully it won't be an ass rapeing. I think I will keep my white one and make it the ultimate DD and sell the black one. At this point, I do not need two cars and two motorcycles :)

KoreanJoey
08-04-2009, 08:32 AM
Hrmm... K, I'll check around.

acidice333
08-05-2009, 02:21 AM
Weeeee... so I was looking at the car today..... a bolt on the manifold is missing so thats why my car dies when idling. and the oil drain bolt is missing...

when the car died on the highway, I did check it for oil and it had oil.. I didn't see anything on the ground either.

hurrah!~ find me a swap joey :)

acidice333
08-05-2009, 05:05 AM
So I decided to take apart my parts 5sfe and get the short block tested cause the guy I bought the engine from said it was cracked... should I be concerned about 2 and 3? goopy rust

http://www.blerb.com/~schong/carstuff/DSC04287%20%5B%5D.JPG

I haven't touched the engine in the car yet..

KoreanJoey
08-05-2009, 08:37 AM
Rust = bad. If it's not too bad might be able to get it cleaned up. If not you'll have to do a slight overbore which means you should do overbored pistons and rings.

acidice333
08-05-2009, 10:41 AM
Its not rusted rusted.. just a small bit of surface? rust.. the majority of it was a couple big goops that was? like rust.

I dunno if I should spend more money on a 5sfe lol.. I should just clean it, hope the short block is fine and slap on my rebuilt head from the blown motor.

while I have a ticking time bomb, you should by then have me a 3sgte :) c'mon c'mon! Good time for you to visit Canada too!

acidice333
08-07-2009, 10:05 PM
What the fudging hell?! So I decided to take the distributor off the blown motor and the key shaft is broken. Wtf? Why do they all keep breaking? Wtf am I doing wrong? Is it that stupid external O-ring causing problems?

VikingJZ
08-10-2009, 06:41 AM
You need a B5234FT

acidice333
08-10-2009, 09:07 AM
http://www.jdmsource.ca/v2/product.asp?ID=26 <-- do I need anything else?