PDA

View Full Version : 3" exhaust for ST184



pitcelica
12-11-2006, 05:17 PM
Hi, I'm swapping to a 3sgte soon and I buy a downpipe 3" in stainless as seen very often on ebay. I buy a mid pipe 3" in stainless like that :

http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=300046168438

And a muffler like that :

http://cgi.ebay.ca/TOYOTA-SUPRA-CELICA-MR2-MR-2-N1-3-TURBO-MUFFLER-EXHAUST_W0QQitemZ160059701175QQihZ006QQcategoryZ33 636QQrdZ1QQcmdZViewItem

I wanna know what other exhaust piping I need to complete my exhaust, how many 90, how many 45 how many straitgh tubing etc.

Or if someone can send me a draw with all measures needed to do my exhaust. I know how to solder so, no clamps or flange.

Helps me plz, I'ts for my St184.

VikingJZ
12-11-2006, 06:57 PM
In all honesty...it would probably be cheaper to take it to a place like Discount Muffler and have them manufacture a custom exhaust for you.

BUT...I think there is one 90 degree bend that goes around the rear suspension on the ST184.

gt lifthback
12-12-2006, 09:36 AM
how about getting one that will fit an alltrac......will it fit our st184 cars i imagine it should be a straight bolt on right?

ciento44
12-12-2006, 03:29 PM
how about getting one that will fit an alltrac......will it fit our st184 cars i imagine it should be a straight bolt on right?

ST184 doesn't have the rear driveshaft, so it is laid out different...

It MAY fit, but it's not really something i would bet on.

AznKlique
12-13-2006, 02:22 AM
Hi, I'm swapping to a 3sgte soon and I buy a downpipe 3" in stainless as seen very often on ebay. I buy a mid pipe 3" in stainless like that :

http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=300046168438

And a muffler like that :

http://cgi.ebay.ca/TOYOTA-SUPRA-CELICA-MR2-MR-2-N1-3-TURBO-MUFFLER-EXHAUST_W0QQitemZ160059701175QQihZ006QQcategoryZ33 636QQrdZ1QQcmdZViewItem

I wanna know what other exhaust piping I need to complete my exhaust, how many 90, how many 45 how many straitgh tubing etc.

Or if someone can send me a draw with all measures needed to do my exhaust. I know how to solder so, no clamps or flange.

Helps me plz, I'ts for my St184.

A few people I know that WELD their own exhausts together generally dont use exact drawings with dimensions. Rather, test fitting and cutting the pipes as you go along usually does the trick. Also, what you can do is remove your current exhaust and just match your bends and lengths to your current exhaust.

Trance4c
12-13-2006, 03:26 AM
No.. an Alltrac or GT4 exhaust will not work! You will have to have one custom made, or if you have access to a welder, do as mentioned above - test, fit, retest, fit and then weld.

gt4wannabe
12-14-2006, 02:28 PM
there are two 90 degree bends before the mid pipe hits the axle back one bending to the right and one bending back towards the rear of the car, and if im not mistaken two 45 degree bends to clear the rear suspension one up and one back down. just go take a good look at your stock exhaust and just go to a custom exhuast shop and let them weld you one.

k2skater
12-25-2006, 12:49 AM
solderd exhaust doesnt sound to safe.... haha it would prob be better to get a cheap mig than to solder it. but even that aint that good. learn how to tig or just spend a few hundred and get one custom made. or you can talk to kteller, maybe they can custom make you one. kteller (http://www.kteller.biz/Default.asp?cookiecheck=yes&)

celfatic
12-28-2006, 03:36 AM
If i can go back, I would buy an all track one and get that one modified. All in all, my 3inch exhaust cost about 6-7 hundred dollars p and l. Kept braking the pipe welded to the flange. Got a 3 inch truck flex pipe and everything is good now. Apex muffler, sounds pretty thrashy but clean. Thats just my opinion. It wont fit garanteed but you can get it modified.